b'Pneumatic ClampsMKR Pneumatic ClampsMKRSFor Round Linear ShaftsNormally Open For Round Linear ShaftsNormally ClosedSize A A1 A2 B1 B2 B3 B4 X G H H1 Holding Holding Part Number Size A A1 A2 B B1 B2 B3 B4 X G H H1Holding Holding Part Number d Force(N) Torque (N)d Force(N) Torque (N)12 50 15 5 37 15 11 18 18 M5 6 27.5 650 4 MKR1200A 12 50 15 5 56 37 15 11 18 18 M5 6 27.5 16 350 2 MKRS1200A16 55 15 5 39 15 12.5 22 22 M5 6 32 650 6 MKR1600A 16 55 15 5 58 39 15 12.5 22 22 M5 6 32 16 400 3 MKRS1600A20 66 45 5 38 18 13 25 25 M8 10 38 1000 10 MKR2000A 20 66 45 5 60 38 18 13 25 25 M8 10 38 20 600 6 MKRS2000A25 77 60 5 43 20 15 30 30 M10 12 43 1200 15 MKR2500A 25 77 60 5 63 43 20 15 30 30 M10 12 43 22 750 9 MKRS2500A30 92 68 5 48.5 25 14 34 35 M10 13 48.5 1750 26 MKR3000A 30 92 68 5 77.5 48.5 25 14 34 35 M10 13 48.5 25 1050 16 MKRS3000A40 120 90 5 49 26 14 45 45 M10 15 62 2000 37 MKR4000A 40 120 90 5 82 49 26 14 45 45 M10 15 62 30 1700 33 MKRS4000A50 132 108 5 49 30 9.5 50 50 M10 15 67 1850 46 MKR5000A 50 132 108 5 82 49 30 9.5 50 50 M10 15 67 30 1650 41 MKRS5000A60 142 108 5 49 30 9.5 50 50 M10 15 67 1850 56 MKR6000A 60 142 108 5 82 49 30 9.5 50 50 M10 15 67 30 1650 49 MKRS6000AOperatingOperating Shaft OperatingOperating ShaftNOTE:Minimum 54 HRC surface hardness of linear shaft required Pressure TemperatureTolerance NOTE:Minimum 54 HRC surface hardness of linear shaft required Pressure TemperatureTolerance3 ~ 6.5 Bar -10 ~ +70 C0.01 mm 5.5 ~ 6.5 Bar -10 ~ +70 C0.01 mmPNEUMATIC CLAMPING ELEMENTS ARE FOR LOCKING LINEAR SHAFTS IN PLACE PNEUMATIC CLAMPING ELEMENTS ARE FOR LOCKING LINEAR SHAFTS IN PLACENOT SUITABLE FOR DYNAMIC BREAKING OR THE SLOWING DOWN OF MOVEMENT NOT SUITABLE FOR DYNAMIC BREAKING OR THE SLOWING DOWN OF MOVEMENT14 TEL: 01827 288122 FAX: 01827 253390 TEL: 01827 288122 FAX: 01827 253390 15sales@wmh-trans.co.ukwww.wmh-trans.co.uk sales@wmh-trans.co.ukwww.wmh-trans.co.uk'